Hyundai Code
Accessing Trouble Codes
With Multi-Use Tester
Except 1993-95 Scoupe
1. Turn ignition switch to Off.
2. Connect harness connector of multi-use tester to diagnostic connector in fuse box, located on left kick panel.
3. Connect power-source terminal of multi-use tester to cigarette lighter socket.
4. Turn ignition switch On, then use multi-use tester to read self-diagnostic codes.
5. Repair any malfunctions found using tester.
6. Turn ignition switch Off, then disconnect battery ground cable for 10 seconds.
7. Check that no malfunction codes are displayed with multi-use tester.
8. Disconnect multi-use tester. If a test is to made during cranking, the power to cigarette lighter will be interrupted therefore, use a separate battery harness for multi-use tester.
With Analog Voltmeter
Except 1993-95 Scoupe
1. Connect voltmeter to self-diagnosis connector, located in fuse box on left kick panel.
2. Turn ignition switch On and note an immediate indication of ECM (ECU) memory contents will begin. If system is in normal condition, pointer of voltmeter indicates a normal pattern. If any abnormality is in the memory, pointer of voltmeter will deflect indicating an abnormal condition.
3. After recording abnormal items, check and repair each part.
4. After repairs have been completed, disconnect battery ground cable for at least 15 seconds to erase codes from memory.
Using On-Board Diagnostic Lamp
1993-95 Scoupe
1. With ignition switch in the On position, ground the No. 10 terminal (L wire) of diagnostic connector for approximately 2.5 seconds.
2. The diagnostic connector is located on the left hand kick panel. The first diagnostic trouble code or no fault detected will be indicated by the on-board diagnostic lamp. The onboard diagnostic lamp will indicated DTC's by flashing frequencies and 2 second pauses. As an example, one flash, followed by a 2 second pause, followed by two flashes and another 2 second pause, followed by two flashes and a 2 second pause, followed by three flashes and another 2 second pause, indicates a failure code 1223. The fault code will be repeated until the No. 10 terminal of the diagnostic connector is grounded to proceed to the next fault code.
3. The last output consist of the end of output code 3333.
Clearing Trouble Codes
To erase any diagnostic codes, disconnect battery ground cable for 15 seconds and the ECM (ECU) memory will be erased.
COMPUTER CODES for Hyundai Vehicles.
If codes other than these are indicated, repeat self-diagnosis.
If codes reappear, substitute a known good ECM, and recheck codes.
CODE
Hyundai Stellar vehicles.
1 Oxygen sensor or circuit
2 Ignition signal
3 Airflow sensor or circuit
4 Atmospheric pressure sensor or circuit
5 Throttle position sensor or circuit
6 Idle Speed Control (ISC) motor position sensor or circuit
7 Coolant temperature sensor or circuit
8 TDC sensor or circuit
9 System normal
CODE
Hyundai Sonata, Excel(90 on),
Scoupe (91 & 92), Elantra.
1 Electronic Control Unit (ECU) (one long needle sweep)
2 ECU system normal
11 Oxygen sensor or circuit
12 Airflow sensor or circuit
13 Intake air temperature sensor or circuit
14 Throttle Position Sensor (TPS) or circuit
15 Motor position sensor or circuit
21 Coolant temperature sensor or circuit
22 Crank angle sensor or circuit
23 TDC sensor or circuit
24 Vehicle Speed Sensor or circuit
25 Barometric pressure sensor or circuit
41 Fuel injector or circuit
42 Fuel pump or circuit
43 EGR system
44 Ignition coil
59 Oxygen sensor
CODE
Hyundai Scoupe (93 through 95) and Accent vehicles.
1122 ECM failure (ROM/RAM)
1169 ECM failure
1233 ECM failure (ROM)
1234 ECM failure (RAM)
2121 Turbo boost sensor control valve
3112 NO. 1 fuel injector
3114 Idle air control (opening failure)
3116 NO. 3 fuel injector
3117 Mass airflow sensor
3121 Turbo boost sensor failure
3122 Idle air control (closing failure)
3128 Heated oxygen sensor
3135 EVAP purge control solenoid valve
3137 Alternator output low
3145 Engine coolant temperature (ECT) sensor
3149 Air conditioning compressor
3152 Turbocharger overboost
3153 Throttle position switch (TPS)
3159 Vehicle speed sensor (VSS)
3211 Knock sensor
3222 Phase sensor
3224 ECM failure (knock evaluation circuit)
3232 Crank position sensor
3233 Same as 3224
3234 NO. 2 fuel injector
3235 NO. 4 fuel injector
3241 ECM failure (injector or purge solenoid)
3242 ECM failure (IAC or air conditioning relay)
3243 ECM failure
4133 ECM failure
4151 Air/fuel control
4152 Air/fuel adaptive failure
4153 Air/fuel multiple adaptive failure
4154 Air/fuel additive adaptive failure
4155 ECM failure (A/C relay, IAC, PCV or injector)
4156 Same as code 3121
4444 Normal
3333 End of trouble codes
